Please select and order
€64.38
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 1163-2

Issue date: 1999 10 01

Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995)

This part of ISO 1163 specifies procedures and conditions for the preparation of test specimens of PVC-U materials in a specified state, and methods for measuring thei...
Withdrawn: 2019 07 01
Publisher:
Austrian Standards International
Format:
Digital | 8 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
This part of ISO 1163 specifies procedures and conditions for the preparation of test specimens of PVC-U materials in a specified state, and methods for measuring their properties. Any property listed in this part and referred to in combination with part 1 shall be determined by the method referred to in this part. No figures are quoted for these properties. Those required for the designation of PVC-U thermoplastics are given in part 1 of this International Standard. All properties shall be determined by the appropriate methods referred to in this part of ISO 1163 and values obtained shall be presented as laid down in ISO 10350. The values determined in accordance with this part of ISO 1163 Will not necessarily be identical to those obtained using specimens of different dimensions and/or prepared by different procedures. The values obtained for the properties of a moulding depend on the moulding compound, the shape, the test method and the state of anisotropy. The last-mentioned depends on the gating of the mould and the moulding conditions, for example temperature, pressure and injection rate. Any subsequent treatment must also be considered, for example conditioning or annealing. The thermal history and the interna1 stresses of the specimens may strongly influence the, thermal and mechanical properties and the resistance to environmental stress cracking, but exert less effect on the electrical properties, which depend mainly on the chemical composition of the moulding compound. In order to obtain reproducible test results, the following two conditions shall be met: - use test specimens with the specified dimensions and conditioning; - use test procedures as specified in this part of ISO 1163.
ÖNORM EN ISO 21306-2
2019 07 01
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Pre...
Norm
ÖNORM EN ISO 1163-2
1999 10 01
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Pre...
Norm
Norm
ISO 1163-1:1995
Issue date : 1995 12 27
Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 1: Designation system and basis for specifications
Norm
ISO 4589-2:1996
Issue date : 1996 07 18
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
Norm
ISO 4589-3:1996
Issue date : 1996 08 08
Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
Norm
ÖNORM EN ISO 178
Issue date : 2005 05 01
Plastics - Determination of flexural properties (ISO 178:2001 + Amd 1:2004) (consolidated version)
Norm
ÖNORM EN ISO 178
Issue date : 2008 09 01
Plastics - Determination of flexural properties (ISO/DIS 178:2008)
Norm
ÖNORM EN ISO 2818
Issue date : 1997 03 01
Plastics - Preparation of test specimens by machining (ISO 2818:1994)
Norm
ÖNORM EN ISO 291
Issue date : 2008 07 01
Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
Norm
ÖNORM EN ISO 306
Issue date : 2004 10 01
Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2004)
Norm
ÖNORM EN ISO 3167
Issue date : 2003 12 01
Plastics - Multipurpose test specimens (ISO 3167:2002)
Norm
ÖNORM EN ISO 4589-3
Issue date : 1996 11 01
Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test (ISO 4589-3:1996)
Norm
ÖNORM EN ISO 527-1
Issue date : 1996 05 01
Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1: 1994)
Norm
ÖNORM EN ISO 527-2
Issue date : 1996 07 01
Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994)
Norm
ÖNORM EN ISO 527-4
Issue date : 1997 09 01
Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997)
Norm
ÖNORM EN ISO 62
Issue date : 2008 05 01
Plastics - Determination of water absorption (ISO 62:2008)
Norm
ÖNORM EN ISO 75-1
Issue date : 2004 09 01
Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2004)
Norm
ÖNORM EN ISO 75-2
Issue date : 2006 09 01
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2004) (consolidated version)
Norm
ÖNORM EN ISO 8256
Issue date : 2005 06 01
Plastics - Determination of tensile-impact strength (ISO 8256:2004)
Norm
ÖNORM EN ISO 899-1
Issue date : 2003 10 01
Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2003)
Norm
ISO 62:1999
Issue date : 1999 02 04
Plastics — Determination of water absorption
Norm
ISO 75-1:1993
Issue date : 1993 08 26
Plastics — Determination of temperature of deflection under load — Part 1: General test method
Norm
ISO 75-2:1993
Issue date : 1993 08 26
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Norm
ISO 178:1993
Issue date : 1993 05 06
Plastics — Determination of flexural properties
Norm
ISO 179:1993
Issue date : 1993 05 06
Plastics — Determination of Charpy impact strength
Norm
ISO 291:1997
Issue date : 1997 07 24
Plastics — Standard atmospheres for conditioning and testing
Norm
ISO 293:1986
Issue date : 1986 10 09
Plastics — Compression moulding test specimens of thermoplastic materials
Norm
ISO 306:1994
Issue date : 1994 07 21
Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
Norm
ISO 527-1:1993
Issue date : 1993 06 10
Plastics — Determination of tensile properties — Part 1: General principles
Norm
ISO 527-2:1993
Issue date : 1993 06 10
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
Norm
ISO 527-4:1997
Issue date : 1997 04 10
Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
Norm
ISO 899-1:1993
Issue date : 1993 12 23
Plastics — Determination of creep behaviour — Part 1: Tensile creep
Norm
ISO 1163-1:1995
Issue date : 1995 12 27
Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 1: Designation system and basis for specifications
Norm
ISO 1183:1987
Issue date : 1987 07 09
Plastics — Methods for determining the density and relative density of non-cellular plastics
Norm
ISO 1210:1992
Issue date : 1992 07 23
Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
Norm
ISO 2818:1994
Issue date : 1994 08 18
Plastics — Preparation of test specimens by machining
Norm
ISO 3167:1993
Issue date : 1993 06 10
Plastics — Multipurpose test specimens
Norm
ISO 4589-2:2017
Issue date : 2017 04 12
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
Norm
ISO 4589-3:2017
Issue date : 2017 04 12
Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
Norm
ISO 8256:1990
Issue date : 1990 12 20
Plastics — Determination of tensile-impact strength
Norm
ISO 10350:1993
Issue date : 1993 12 23
Plastics — Acquisition and presentation of comparable single-point data
Norm
ÖNORM EN ISO 21306-2
Issue date : 2019 07 01
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21306-2:2019)
Norm
ISO 1163-2:1995
Issue date : 1995 08 03
Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties