Please select and order
€64.38
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 3167

Issue date: 2003 12 01

Plastics - Multipurpose test specimens (ISO 3167:2002)

This International Standard specifies requirements relating to multipurpose test specimens for plastic moulding materials intended for processing by injection or direct ...
Withdrawn: 2014 03 01
Publisher:
Austrian Standards International
Format:
Digital | 14 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
This International Standard specifies requirements relating to multipurpose test specimens for plastic moulding materials intended for processing by injection or direct compression moulding. Specimens of types A and B are tensile test specimens from which, with simple machining, specimens for a variety of other tests can be taken (see annex A). Because they have such wide utility, these tensile specimens are referred to in this International Standard as multipurpose test specimens. The principal advantage of a multipurpose test specimen is that it allows all the test methods mentioned in annex A to be carried out on the basis of comparable mouldings. Consequently, the properties measured are coherent as all are measured with specimens in the same state. In other words, it can be expected that test results for a given set of specimens will not vary appreciably due to unintentionally different moulding conditions. On the other hand, if desired, the influence of moulding conditions and/or different states of the specimens can be assessed without difficulty for all of the properties measured. For quality-control purposes, the multipurpose test specimen may serve as a convenient source of further specimens not readily available. Furthermore, the fact that only one mould is required may be advantageous. The use of multipurpose test specimens shall be agreed upon by the interested parties, because there may be significant differences between properties of the multipurpose test specimens and those specified in the relevant test methods. The main modification with respect to the previous edition of this International Standard lies in narrowing the tolerances on the radius of the shoulder of specimen types A and B. Taking into account the fact that many moulds based on the previous edition are still in use, the changes are introduced as recommendations only. It is intended to change from recommended to manda (...abbreviated)
ÖNORM EN ISO 3167
2003 12 01
Plastics - Multipurpose test specimens (ISO 3167:2002)
Norm
ÖNORM EN ISO 3167
1997 03 01
Plastics - Multipurpose-test specimens (ISO 3167:1993)
Norm
Norm
ISO 295:2004
Issue date : 2004 01 14
Plastics — Compression moulding of test specimens of thermosetting materials
Norm
ÖNORM EN ISO 2818
Issue date : 1997 03 01
Plastics - Preparation of test specimens by machining (ISO 2818:1994)
Norm
ÖNORM EN ISO 294-1
Issue date : 1998 10 01
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996)
Norm
ÖNORM EN ISO 295
Issue date : 2004 05 01
Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004)
Norm
ÖNORM EN ISO 10724-1
Issue date : 2002 04 01
Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of mulitpurpose test specimens (ISO 10724-1:1998)
Norm
ISO 293:1986
Issue date : 1986 10 09
Plastics — Compression moulding test specimens of thermoplastic materials
Norm
ISO 294-1:1996
Issue date : 1996 12 26
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
Norm
ISO 295:2004
Issue date : 2004 01 14
Plastics — Compression moulding of test specimens of thermosetting materials
Norm
ISO 2818:1994
Issue date : 1994 08 18
Plastics — Preparation of test specimens by machining
Norm
ISO 10724-1:1998
Issue date : 1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
Norm
ISO 3167:2002
Issue date : 2002 03 07
Plastics — Multipurpose test specimens