Please select and order
€64.38
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 21306-2

Issue date: 2019 07 01

Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21306-2:2019)

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PVC-U moulding and extrusion materia...
Valid
Publisher:
Austrian Standards International
Format:
Digital | 11 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PVC-U moulding and extrusion materials. Requirements for handling test materials and for conditioning both the test material before moulding and the specimens before testing are given. The properties required for the designation of PVC-U thermoplastics are given in ISO 21306-1. All properties are intended to be determined by the appropriate methods referred to in this document and values obtained shall be presented as laid down in ISO 10350-1. The values determined in accordance with this document are not necessarily be identical to those obtained using specimens of different dimensions and/or prepared by different procedures. The values obtained for the properties of a moulding depend on the moulding compound, the shape, the test method and the state of anisotropy. The last-mentioned depends on the gating of the mould and the moulding conditions, for example temperature, pressure and injection rate. Any subsequent treatment is also be considered, for example conditioning or annealing. The thermal history and the internal stresses of the specimens can strongly influence the thermal and mechanical properties and the resistance to environmental stress cracking, but exert less effect on the electrical properties, which depend mainly on the chemical composition of the moulding compound. In order to obtain reproducible and comparable test results, the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein are used. Values determined are not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
ÖNORM EN ISO 21306-2
2019 07 01
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Pre...
Norm
ÖNORM EN ISO 1163-2
1999 10 01
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Pre...
Norm
Norm
ISO 21306-2:2019
Issue date : 2019 03 04
Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 62:2008
Issue date : 2008 02 01
Plastics — Determination of water absorption
Norm
ISO 75-1:2020
Issue date : 2020 02 28
Plastics — Determination of temperature of deflection under load — Part 1: General test method
Norm
ISO 75-2:2013
Issue date : 2013 04 09
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Norm
ISO 179-1:2010
Issue date : 2010 06 04
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
Norm
ISO 179-2:2020
Issue date : 2020 05 14
Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
Norm
ISO 291:2008
Issue date : 2008 04 22
Plastics — Standard atmospheres for conditioning and testing
Norm
ISO 293:2004
Issue date : 2004 05 11
Plastics — Compression moulding of test specimens of thermoplastic materials
Norm
ISO 306:2013
Issue date : 2013 11 08
Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
Norm
ISO 527-1:2019
Issue date : 2019 07 26
Plastics — Determination of tensile properties — Part 1: General principles
Norm
ISO 527-2:2012
Issue date : 2012 02 22
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
Norm
ISO 527-4:1997
Issue date : 1997 04 10
Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
Norm
ISO 1183-1:2019
Issue date : 2019 02 28
Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method (Corrected version 2019-05)
Norm
ISO 1183-2:2019
Issue date : 2019 02 28
Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method
Norm
ISO 1183-3:1999
Issue date : 1999 09 30
Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method
Norm
ISO 2818:2018
Issue date : 2018 12 13
Plastics — Preparation of test specimens by machining
Norm
ISO 4589-2:2017
Issue date : 2017 04 12
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
Norm
ISO 4589-3:2017
Issue date : 2017 04 12
Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
Norm
ISO 8256:2004
Issue date : 2004 07 02
Plastics — Determination of tensile-impact strength
Norm
ISO 10350-1:2017
Issue date : 2017 10 11
Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
Norm
ISO 20753:2018
Issue date : 2018 10 19
Plastics — Test specimens
Norm
ISO 21306-1:2019
Issue date : 2019 03 04
Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 1: Designation system and basis for specifications
Norm
IEC 60695-11-10
Issue date : 1999 03 31
Fire hazard testing Test flames -- 50 W horizontal and vertical flame test methods