Please select and order
€134.80
excl. VAT
Add to cart
Norm
ÖNORM EN 286-4
Issue date: 1995 01 01
Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressure vessels designed for air braking equipment and auxiliary .......(abbreviated)
1.1 This Part of this European Standard is applicable to simple
unfired aluminium alloy pressure vessels, referred to as "vessel" in this standard, designed for air brak...
Valid
§ Legal References
Publisher:
Austrian Standards International
Format:
Digital | 28 Pages
Language:
German
| English
| Download GER/ENG
Optionally co-design standards:
ICS
1.1 This Part of this European Standard is applicable to simple
unfired aluminium alloy pressure vessels, referred to as "vessel" in this standard, designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock (see 1.6).
1.2 The vessels to this standard are:
a) made from a single shell;
b) made from aluminium alloy;
c) fabricated by welding;
d) used at a maximum working pressure of 10 bar;
e) the product of the maximum working pressure (in bar) and the volume (in litre):
50 bar litres < PV <= 10 000 bar litres;
f) made of a cylindrical part of circular cross-section called the shell with two outwardly dished torispherical ends, that is two dished ends with the same axis of rotation. This standard therefore does not apply to vessels with one or two flat ends or those made up of several compartments;
g) calculated with a design pressure P (see 5.1.4.2);
h) designed for a working temperature of between -50 °C and +100 °C (+ 65 °C for certain grades of aluminium alloy
(see 4.1.1)];
j) fastened to the vehicles by straps;
1.3 In normal service, a momentary overpressure of 1 bar of the maximum working pressure is permitted (10 % of PS).
1.4 This Part of this European Standard applies to the vessel
proper, from the inlet connection to the outlet connection and to all other connections and fittings belonging to the vessel.
1.5 This Part of this European Standard gives the requirements to be met for the calculation, design, fabrication, inspection during fabrication and certification of the vessel, and fittings for assembly to the vehicle.
These requirements cannot be written in sufficient detail to ensure good workmanship or proper construction. Each manufacturer is therefore responsible for taking every necessary step to make sure that the quality of workmanship and construction is such as to ensure compliance with good engineering practice.
ÖNORM EN 286-4
1995 01 01
Simple unfired pressure vessels designed to contain air or nitrogen - Part 4: Aluminium alloy pressu...
Norm
↖
Norm
Issue date :
2004 12 09
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
Norm
Issue date :
2008 12 10
Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel
Norm
Issue date :
2007 01 15
Aluminium and aluminium alloys — Wrought products — Temper designations
Norm
Issue date :
2000 09 21
Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation
Norm
Issue date :
1981 10 01
Chromate conversion coatings on electroplated zinc and cadmium coatings
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 1: General technical delivery conditions
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
Norm
Issue date :
2005 02 01
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
Norm
Issue date :
2004 03 01
Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
Norm
Issue date :
2005 01 01
Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
Norm
Issue date :
2005 07 01
Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
Norm
Issue date :
2005 04 01
Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
Norm
Issue date :
1989 08 24
Wrought aluminium and aluminium alloys — Chemical composition and forms of products — Part 1: Chemical composition
Norm
Issue date :
1989 08 24
Wrought aluminium and aluminium alloys — Chemical composition and forms of products — Part 2: Forms of products
Norm
Issue date :
2017 02 01
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
Norm
Issue date :
2018 02 15
Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel
Norm
Issue date :
2007 01 15
Aluminium and aluminium alloys — Wrought products — Temper designations
Norm
Issue date :
1972 10 01
Recommended practice for the X-ray inspection of fusion welded butt joints for aluminium and its alloys and magnesium and its alloys 5 to 50 mm thick
Norm
Issue date :
1981 10 01
Chromate conversion coatings on electroplated zinc and cadmium coatings
Norm
Issue date :
2014 09 08
Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 2: Mechanical properties
Norm
Issue date :
2014 09 10
Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties