Please select and order
€109.76
excl. VAT
Add to cart
Norm
ÖNORM EN 1555-3
Issue date: 2005 10 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings (consolidated version)
This part of EN 1555 specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical
fittings made from PE and other materials for ...
Withdrawn: 2011 06 01
§ Legal References
Publisher:
Austrian Standards International
Format:
Digital | 30 Pages
Language:
German
| English
Currently valid:
Optionally co-design standards:
This part of EN 1555 specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical
fittings made from PE and other materials for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with the other parts of EN 1555 (see Foreword), it is applicable to PE fittings, their joints and to joints with
components of PE and other materials intended to be used under the following conditions:
a maximum operating pressure, MOP, up to and including 10 bar 1);
an operating temperature of 20 °C as reference temperature.
NOTE 1 For other operating temperatures, derating coefficients should be used, see EN 1555-5.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This standard is applicable for fittings of the following types:
electrofusion socket fittings;
electrofusion saddle fittings;
spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
mechanical fittings.
The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps.
ÖNORM EN 1555-3
2022 01 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Norm
ÖNORM EN 1555-3
2013 04 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Norm
ÖNORM EN 1555-3
2011 06 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Norm
ÖNORM EN 1555-3
2005 10 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings (cons...
Norm
↖
ÖNORM EN 1555-3
2003 08 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Norm
ÖNORM B 5192
2001 01 01
Buried pipes, joints and fittings of polyethylene (PE 80 and PE 100) for the transport of gaseous fu...
Norm
ÖNORM B 5192
1987 05 01
Buried pipes, joints and fittings of polyethylene (PE) for the transport of gaseous fuels; dimension...
Norm
ÖNORM B 5192
1985 05 01
Buried pipes, joints and fittings of polyethylene (PE) for the transport of gaseous fuels; dimension...
Norm
Norm
Issue date :
1994 05 12
Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation
Norm
Issue date :
2000 09 21
Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation
Norm
Issue date :
2000 06 22
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
Norm
Issue date :
2000 06 29
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
Norm
Issue date :
2001 03 29
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
Norm
Issue date :
2001 10 25
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
Norm
Issue date :
1997 12 25
Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
Norm
Issue date :
1997 12 25
Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies
Norm
Issue date :
2006 07 01
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
Norm
Issue date :
2006 07 01
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
Norm
Issue date :
1997 11 01
Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
Norm
Issue date :
1997 11 01
Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee
Norm
Issue date :
1998 05 01
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
Norm
Issue date :
2005 10 01
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005)
Norm
Issue date :
2006 09 01
Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids (consolidated version)
Norm
Issue date :
2011 06 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
Norm
Issue date :
2011 06 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
Norm
Issue date :
2005 06 01
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
Norm
Issue date :
2011 06 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
Norm
Issue date :
1994 05 12
Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation
Norm
Issue date :
2000 06 22
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
Norm
Issue date :
2000 06 29
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
Norm
Issue date :
2001 03 29
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels — Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
Norm
Issue date :
2001 10 25
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
Norm
Issue date :
1997 12 25
Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
Norm
Issue date :
1997 12 25
Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies
Norm
Issue date :
2011 06 01
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings