Please select and order
€98.22
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 1133

Issue date: 2005 10 01

Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005)

This International Standard specifies two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic material...
Withdrawn: 2012 03 15
Publisher:
Austrian Standards International
Format:
Digital | 21 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
This International Standard specifies two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic materials under specified conditions of temperature and load. Procedure A is a mass-measurement method. Procedure B is a displacement-measurement method. Normally, the test conditions for measurement of melt flow rate are specified in the material standard with a reference to this International Standard. The test conditions normally used for thermoplastics are listed in Annexes A and B. The MVR will be found particularly useful when comparing materials of different filler content and when comparing filled with unfilled thermoplastics. The MFR can be determined from MVR measurements provided the melt density at the test temperature and pressure is known. These methods are in principle also applicable to thermoplastics for which the rheological behaviour is affected during the measurement by phenomena such as hydrolysis, condensation or crosslinking, but only if the effect is limited in extent and only if the repeatability and reproducibility are within an acceptable range. For materials which show significantly affected rheological behaviour during testing, these methods are not appropriate. In such cases, the use of the viscosity number in dilute solution, determined in accordance with the relevant part of ISO 1628, is recommended for characterization purposes. NOTE The rates of shear in these methods are much smaller than those used under normal conditions of processing, and therefore data obtained by these methods for various thermoplastics may not always correlate with their behaviour during processing. Both methods are used primarily in quality control.
ÖNORM EN ISO 1133-1
2022 11 15
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermop...
Norm
ÖNORM EN ISO 1133-2
2012 03 15
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermop...
Norm
ÖNORM EN ISO 1133-1
2012 03 15
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermop...
Norm
ÖNORM EN ISO 1133
2005 10 01
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of the...
Norm
ÖNORM EN ISO 1133
1999 11 01
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of the...
Norm
Expand
Norm
ISO 8986-2:2009
Issue date : 2009 10 30
Plastics — Polybutene-1 (PB-1) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 1622-2:1995
Issue date : 1995 04 27
Plastics — Polystyrene (PS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 1872-2:2007
Issue date : 2007 01 26
Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 1873-2:2007
Issue date : 2007 08 28
Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 2580-2:2003
Issue date : 2003 11 28
Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 2897-2:2003
Issue date : 2003 11 28
Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 4287:1997
Issue date : 1997 04 03
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
Norm
ISO 4613-2:1995
Issue date : 1995 08 10
Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 4894-2:1995
Issue date : 1995 04 27
Plastics — Styrene/acrylonitrile (SAN) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 6402-2:2003
Issue date : 2003 11 28
Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 6507-1:2005
Issue date : 2005 12 08
Metallic materials — Vickers hardness test — Part 1: Test method
Norm
ISO 7391-2:2006
Issue date : 2006 03 02
Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 8257-2:2001
Issue date : 2001 12 20
Plastics — Poly(methyl methacrylate) (PMMA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties (Corrected version 2003-11)
Norm
ISO 9988-2:2006
Issue date : 2006 07 13
Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 10366-2:2003
Issue date : 2003 11 28
Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 15494:2003
Issue date : 2003 04 14
Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE) and polypropylene (PP) — Specifications for components and the system — Metric series (Corrected version 2004-01)
Norm
ISO 15876-3:2003
Issue date : 2003 12 08
Plastics piping systems for hot and cold water installations — Polybutylene (PB) — Part 3: Fittings
Norm
ISO 1622-2:1995
Issue date : 1995 04 27
Plastics — Polystyrene (PS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 1872-2:2007
Issue date : 2007 01 26
Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 1873-2:2007
Issue date : 2007 08 28
Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 2580-2:2003
Issue date : 2003 11 28
Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 2897-2:2003
Issue date : 2003 11 28
Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 4287:1997
Issue date : 1997 04 03
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
Norm
ISO 4613-2:1995
Issue date : 1995 08 10
Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 4894-2:1995
Issue date : 1995 04 27
Plastics — Styrene/acrylonitrile (SAN) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 6402-2:2003
Issue date : 2003 11 28
Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 6507-1:2018
Issue date : 2018 01 10
Metallic materials — Vickers hardness test — Part 1: Test method
Norm
ISO 7391-2:2006
Issue date : 2006 03 02
Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 10366-2:2003
Issue date : 2003 11 28
Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ISO 15494:2015
Issue date : 2015 09 29
Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system
Norm
ISO 15876-3:2017
Issue date : 2017 01 10
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
Norm
ISO 8986-2:2009
Issue date : 2009 10 30
Plastics — Polybutene-1 (PB-1) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
Norm
ÖNORM EN ISO 1133-1
Issue date : 2012 03 15
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
Norm
ÖNORM EN ISO 1133-2
Issue date : 2012 03 15
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
Norm
ISO 1133:2005
Issue date : 2005 06 07
Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics