Please select and order
€171.12
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 23856

Issue date: 2022 01 15

Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 23856:2021)

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It i...
Valid
This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations. The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering. This document is applicable to circular pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.
ÖNORM EN ISO 23856
2022 01 15
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-rei...
Norm
ÖNORM EN 14364
2013 04 15
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
ÖNORM EN 1796
2013 04 15
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting p...
Norm
ÖNORM EN 1796
2009 09 15
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting p...
Norm
ÖNORM EN 14364
2009 04 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
ÖNORM EN 1796
2009 04 01
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting p...
Norm
ÖNORM EN 14364
2006 08 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
ÖNORM EN 1796
2006 08 01
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting p...
Norm
ÖNORM B 5162
2002 11 01
Glass fibre reinforced plastic pipes - Wound pipes, joints and fittings made of GF-UP - Dimensions, ...
Norm
ÖNORM B 5162
2002 11 01
Glass fibre reinforced plastic pipes - Wound pipes, joints and fittings made of GF-UP - Dimensions, ...
Norm
ÖNORM B 5161/AC1
2002 02 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM B 5161/AC1
2002 02 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM B 5161
2001 11 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM B 5161
2001 11 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM EN 1636-5
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plas...
Norm
ÖNORM EN 1115-1
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM EN 1636-3
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plas...
Norm
ÖNORM EN 1115-3
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM EN 1115-5
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM B 5161
1983 10 01
Glass fibre reinforced plastic pipes; GF-UP-centrifugally cast pipes, joints and fittings; dimension...
Norm
ÖNORM B 5161
1983 10 01
Glass fibre reinforced plastic pipes; GF-UP-centrifugally cast pipes, joints and fittings; dimension...
Norm
Expand
Norm
ISO 75-2:2013
Issue date : 2013 04 09
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Norm
ISO 161-1:2018
Issue date : 2018 01 08
Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series
Norm
ISO 527-4:1997
Issue date : 1997 04 10
Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
Norm
ISO 527-5:2009
Issue date : 2009 06 26
Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
Norm
ISO 1452-3:2009
Issue date : 2009 12 01
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 3: Fittings (Corrected version 2010-02)
Norm
ISO 2394:2015
Issue date : 2015 03 04
General principles on reliability for structures
Norm
ISO 2531:2009
Issue date : 2009 12 08
Ductile iron pipes, fittings, accessories and their joints for water applications
Norm
ISO 3126:2005
Issue date : 2005 03 16
Plastics piping systems — Plastics components — Determination of dimensions
Norm
ISO 4200:1991
Issue date : 1991 02 21
Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
Norm
ISO 7432:2021
Issue date : 2021 04 30
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
Norm
ISO 7509:2015
Issue date : 2015 03 04
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of time to failure under sustained internal pressure
Norm
ISO 7685:2019
Issue date : 2019 07 11
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial ring stiffness
Norm
ISO 8483:2019
Issue date : 2019 08 02
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
Norm
ISO 8513:2016
Issue date : 2016 01 26
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
Norm
ISO 8521:2020
Issue date : 2020 07 09
Glass-reinforced thermosetting plastic (GRP) pipes — Test methods for the determination of the initial circumferential tensile wall strength
Norm
ISO 8533:2019
Issue date : 2019 08 02
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of cemented or wrapped joints
Norm
ISO 8639:2016
Issue date : 2016 02 18
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints
Norm
ISO 10466:2021
Issue date : 2021 04 12
Glass-reinforced thermosetting plastics (GRP) pipes — Test method to prove the resistance to initial ring deflection
Norm
ISO 10468:2018
Issue date : 2018 05 03
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions
Norm
ISO 10471:2018
Issue date : 2018 05 17
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
Norm
ISO 10928:2016
Issue date : 2016 12 14
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
Norm
ISO 10952:2021
Issue date : 2021 03 31
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition
Norm
ISO 11922-1:2018
Issue date : 2018 01 08
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
Norm
ISO 18851:2015
Issue date : 2015 03 16
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test method to prove the structural design of fittings
Norm
ISO 23856:2021
Issue date : 2021 06 15
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin