Please select and order
€160.20
excl. VAT
Add to cart
Norm
ÖNORM EN 14364
Issue date: 2006 08 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
This European Standard specifies the required properties of the piping system and its components made from
glass-reinforced thermosetting plastics (GRP) based on unsatur...
Withdrawn: 2009 04 01
§ Legal References
Publisher:
Austrian Standards International
Format:
Digital | 75 Pages
Language:
German
| English
Currently valid:
Optionally co-design standards:
This European Standard specifies the required properties of the piping system and its components made from
glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used
for drainage or sewerage with or without pressure. In a pipework system, pipes and fittings of different nominal
pressure and stiffness ratings may be used together.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.37 and 3.38), primarily
intended for use in buried installations.
NOTE 2 Piping systems conforming to this European Standard can be used also for non-buried applications provided
the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes,
fittings and joints.
It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 3000, which are intended
to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without
pressure.
This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures.
Clause 4 specifies the general aspects of GRP-UP piping system intended to be used in the field of drainage
or sewerage, with or without pressure.
Clause 5 specifies the characteristics of pipes made from GRP-UP with or without aggregates and/or fillers.
The pipes can have a thermosetting or thermoplastics liner. Clause 5 also specifies the test parameters for the
test methods referred to in this European Standard.
Clause 6 specifies the characteristics of fittings made from GRP-UP with either a thermosetting or
thermoplastics liner intended to be used in the field of drainage or sewerage. Clause 6 specifies the
dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors and
it also specifies the test parameters for the test methods referred to in this European Standard.
Clause 6 is applicable to fittings made using any of the following techniques:
a) fabricated from straight pipe;
b) moulded by
1) filament winding;
2) tape winding;
3) contact moulding;
4) hot or cold press moulding.
Clause 7 is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of
water, both buried and non-buried. This specification is applicable to joints, which are or are not intended to be
resistant to axial loading. It covers requirements to prove the design of the joint. Clause 7 specifies type test
performance requirements for the following joints as a function of the declared nominal pressure rating of the
pipeline or system:
i) socket-and-spigot (either integral with pipe or sleeve coupling) or mechanical joint;
ii) locked socket-and-spigot joint;
iii)cemented or wrapped joint;
iv) bolted flange joint.
ÖNORM EN ISO 23856
2022 01 15
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-rei...
Norm
ÖNORM EN 14364
2013 04 15
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
ÖNORM EN 14364
2009 04 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
ÖNORM EN 14364
2006 08 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo...
Norm
↖
ÖNORM B 5162
2002 11 01
Glass fibre reinforced plastic pipes - Wound pipes, joints and fittings made of GF-UP - Dimensions, ...
Norm
ÖNORM B 5161/AC1
2002 02 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM B 5161
2001 11 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP -...
Norm
ÖNORM EN 1115-1
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM EN 1636-3
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plas...
Norm
ÖNORM EN 1115-3
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM EN 1636-5
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plas...
Norm
ÖNORM EN 1115-5
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced ther...
Norm
ÖNORM B 5161
1983 10 01
Glass fibre reinforced plastic pipes; GF-UP-centrifugally cast pipes, joints and fittings; dimension...
Norm
Norm
Issue date :
2007 04 01
Plastics piping systems for water supply and for drainage and sewerage with or without pressure - Pipes, joints and fittings made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Supplementary requirements to ÖNORM EN 1796 and ÖNORM EN 14364 as well as procedure for the proof of conformity
Norm
Issue date :
2009 04 01
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) (consolidated version)
Norm
Issue date :
2002 07 11
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
Norm
Issue date :
2003 11 21
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
Norm
Issue date :
2003 11 21
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints
Norm
Issue date :
2003 11 21
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
Norm
Issue date :
2003 11 21
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
Norm
Issue date :
2003 11 21
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor
Norm
Issue date :
1994 11 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analyses and their use
Norm
Issue date :
1997 07 01
Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of ....(abbreviated)
Norm
Issue date :
1997 07 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of ....(abbreviated)
Norm
Issue date :
1997 01 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
Norm
Issue date :
1997 01 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
Norm
Issue date :
1997 02 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties
Norm
Issue date :
1997 02 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
Norm
Issue date :
1997 02 01
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
Norm
Issue date :
1997 09 01
Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997)
Norm
Issue date :
1997 09 01
Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:1997)
Norm
Issue date :
2006 09 01
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2004) (consolidated version)
Norm
Issue date :
2005 06 01
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
Norm
Issue date :
2022 01 15
Plastics piping systems for water supply and for drainage and sewerage with or without pressure - Pipes, joints and fittings made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Supplementary requirements to ÖNORM EN ISO 23856
Norm
Issue date :
2022 01 15
Plastics piping systems for water supply and for drainage and sewerage with or without pressure - Pipes, joints and fittings made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Supplementary requirements to ÖNORM EN ISO 23856
Norm
Issue date :
2002 02 01
Glass fibre reinforced plastic pipes - Centrifugally cast pipes, joints and fittings made of GF-UP - Dimensions, requirements, tests and quality assurance (Corrigendum)
Norm
Issue date :
2002 11 01
Glass fibre reinforced plastic pipes - Wound pipes, joints and fittings made of GF-UP - Dimensions, requirements, tests and marking of conformity
Norm
Issue date :
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General
Norm
Issue date :
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings
Norm
Issue date :
1999 05 01
Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints
Norm
Issue date :
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings
Norm
Issue date :
1999 05 01
Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints
Norm
Issue date :
2013 04 15
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
Norm
Issue date :
2021 04 30
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
Norm
Issue date :
2019 08 02
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
Norm
Issue date :
2019 08 02
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of cemented or wrapped joints
Norm
Issue date :
2018 05 03
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions
Norm
Issue date :
2018 05 17
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
Norm
Issue date :
2003 11 21
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor
Norm
Issue date :
2009 04 01
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermo-setting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints