Please select and order
€98.22
excl. VAT
Add to cart
Norm

ÖNORM EN 10326

Issue date: 2004 10 01

Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions

1.1 This document specifies requirements for continuously hot-dip coated products made of structural steels coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium al...
Withdrawn: 2009 05 01
1.1 This document specifies requirements for continuously hot-dip coated products made of structural steels coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) (see Table 1) with thicknesses from 0,35 mm up to 3,0 mm unless otherwise agreed (see 1.2). The thickness is the final thickness of the delivered product after coating. This document applies to strip of all widths and to sheets cut from it ( 600 mm width) and cut lengths (< 600 mm width). 1.2 If agreed at the time of enquiry and order, this document may also be applied to continuously hot-dip coated flat products in thicknesses > 3,0 mm. In this case the mechanical property, adhesion of coating and surface condition requirements shall also be agreed at the time of enquiry and order. 1.3 The products covered by this document are mainly used where minimum yield strength and corrosion resistance are the most important factors. Corrosion resistance of the alloy is proportional to the coating thickness, hence to its mass (see also 7.3.2). NOTE +ZF coated products should not be used without additional organic coating. 1.4 This document is not applicable to: continuously hot-dip coated flat products of low-carbon steel strip and sheet for cold forming (see EN 10327); electrolytic galvanized cold rolled steel flat products (see EN 10152); continuously organic coated (coil coated) flat steel products (see EN 10169-1, ENV 10169-2 and EN 10169-3); continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming (see EN 10292).
ÖNORM EN 10346
2015 11 01
Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
Norm
ÖNORM EN 10346
2009 05 01
Continuously hot-dip coated steel flat products - Technical delivery conditions
Norm
ÖNORM EN 10326
2004 10 01
Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions
Norm
ÖNORM EN 10154
2002 11 01
Continuously hot-dip aluminium-silicon (AS) coated steel strip and sheet - Technical delivery condit...
Norm
ÖNORM EN 10147
2000 08 01
Continuously hot-dip zinc coated structural steels strip and sheet - Technical delivery conditions
Norm
ÖNORM EN 10154
1996 08 01
Continuously hot-dip aluminium-silicon (AS) coated steel strip and sheet - Technical delivery condit...
Norm
ÖNORM EN 10147
1996 03 01
Continuously hot-dip zinc coated structural steel strip and sheet - Technical delivery conditions
Norm
ÖNORM EN 10215
1995 05 01
Continuously hot-dip aluminium-zinc (AZ) coated steel strip and sheet - Technical delivery condition...
Norm
ÖNORM EN 10214
1995 05 01
Continuously hot-dip zinc-aluminium (ZA) coated steel strip and sheet - Technical delivery condition...
Norm
ÖNORM EN 10147
1992 04 01
Continuously hot-dip zinc coated structural steel sheet and strip - Technical delivery conditions
Norm
Expand
Norm
ÖNORM EN 10002-1
Issue date : 2002 01 01
Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature
Norm
ÖNORM EN 10020
Issue date : 2000 06 01
Definition and classification of grades of steel
Norm
ÖNORM EN 10021
Issue date : 2007 04 01
General technical delivery conditions for steel products
Norm
ÖNORM EN 10027-1
Issue date : 2006 02 01
Designation systems for steels - Part 1: Steel names
Norm
ÖNORM EN 10027-2
Issue date : 1992 12 01
Designation systems for steel - Numerical system
Norm
ÖNORM EN 10079
Issue date : 2007 08 01
Definition of steel products
Norm
ÖNORM EN 10143
Issue date : 2006 10 01
Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
Norm
ÖNORM EN 10204
Issue date : 2005 01 01
Metallic products - Types of inspection documents
Norm
ÖNORM EN 10346
Issue date : 2009 05 01
Continuously hot-dip coated steel flat products - Technical delivery conditions