Please select and order
€134.80
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 898-1

Issue date: 1999 12 01

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999)

This part of ISO 898 specifies the mechanical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 1...
Withdrawn: 2009 10 01
§ Legal References
Publisher:
Austrian Standards International
Format:
Digital | 31 Pages
Language:
German | English
Optionally co-design standards:
This part of ISO 898 specifies the mechanical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Products conforming to the requirements of this part of ISO 898 are evaluated only in the ambient temperature range and may not retain the specified mechanical and physical properties at higher and lower temperatures. Attention is drawn to annex A which provides examples of lower yield stress and stress at 0,2 % non-proportional elongation at elevated temperatures. At temperatures lower than the ambient temperature range, a significant change in the properties, particularly impact strength, may occur. When fasteners are to be used above or below the ambient temperature range it is the responsibility of the user to ensure that the mechanical and physical properties are suitable for his particular service conditions. Certain fasteners may not fulfill the tensile or torsional requirements of this part of ISO 898 because of the geometry of the head which reduces the shear area in the head as compared to the stress area in the thread such as countersunk, raised countersunk and cheese heads (see clause 6). This part of ISO 898 applies to bolts, screws and studs with coarse pitch thread M1,6 to M39, and fine pitch thread M8 3 1 to M39 3 3; with triangular ISO thread in accordance with ISO 68-1; with diameter/pitch combinations in accordance with ISO 261 and ISO 262; with thread tolerance in accordance with ISO 965-1 and ISO 965-2; made of carbon steel or alloy steel. It does not apply to set screws and similar threaded fasteners not under tensile stresses (see ISO 898-5). It does not specify requirements for such properties as weldability; corrosion-resistance; ability to withstand temperatures above 1 300 °C (1 250 °C for 10.9) or below 2 50 °C; resistance to shear stress; fatigue resistance. NOTE (...abbreviated)
ÖNORM EN ISO 898-1
2013 04 15
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and ...
Norm
ÖNORM EN ISO 898-1
2009 10 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and ...
Norm
ÖNORM EN ISO 898-1
1999 12 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and ...
Norm
ÖNORM EN 20898-1
1991 12 01
Mechanical properties of fasteners - Bolts, screws and studs
Norm
ÖNORM ISO 898-1
1989 10 01
Mechanical properties of fasteners; bolts, screws and studs
Norm
ÖNORM ISO 898-1
1981 01 01
Mechanical properties of fasterners; bolts, screws and studs
Norm
ÖNORM M 5001-3
1977 10 01
Fasteners and similar parts; technical specifications; property classes and test methods for bolts s...
Vornorm
ÖNORM M 5001-7
1976 08 01
Fasteners and similar parts; technical specifications, marking and delivery of bolts, screws and stu...
Norm
ÖNORM M 5001
1958 02 03
Schrauben, Muttern, Scheiben und ähnliche Gewinde-und Formteile; technische Lieferbedingungen
Norm
ÖNORM M 5001
1923 01 31
Blanke Sechskantschrauben für 1 und 2 Muttern oder 1 Kronenmutter von 1,7 - 10 mm; metrisches Gewind...
Norm
Expand
Norm
ÖNORM EN 20273
Issue date : 1992 05 01
Fasteners - Clearance holes for bolts and screws
Norm
ÖNORM EN 26157-1
Issue date : 1992 03 01
Fasteners - Surface discontinuities - Bolts, screws and studs for general requirements
Norm
ÖNORM EN 26157-3
Issue date : 1992 03 01
Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements
Norm
ÖNORM EN 20898-2
Issue date : 1994 05 01
Mechanical properties of fasteners - Part 2 : Nuts with specified proof load values - Coarse thread (ISO 898-2:1992)
Norm
ÖNORM EN 20898-7
Issue date : 1995 06 01
Mechanical properties of fasteners - Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm (ISO 898-7:1992)
Norm
ÖNORM EN ISO 6507-1
Issue date : 2006 10 01
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2005)
Norm
ÖNORM EN ISO 898-5
Issue date : 1998 11 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners not under tensile stresses (ISO 898-5:1998)
Norm
ISO 6892:1998
Issue date : 1998 03 05
Metallic materials — Tensile testing at ambient temperature
Norm
ISO 83:1976
Issue date : 1976 11 01
Steel — Charpy impact test (U-notch)
Norm
ISO 261:1998
Issue date : 1998 12 20
ISO general purpose metric screw threads — General plan
Norm
ISO 262:1998
Issue date : 1998 12 20
ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
Norm
ISO 273:1979
Issue date : 1979 06 01
Fasteners — Clearance holes for bolts and screws (Corrected version 1992-07)
Norm
ISO 724:1978
Issue date : 1978 11 01
ISO metric screw threads — Basic dimensions
Norm
ISO 898-2:1992
Issue date : 1992 11 12
Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse thread
Norm
ISO 898-5:1998
Issue date : 1998 07 23
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners not under tensile stresses
Norm
ISO 898-7:1992
Issue date : 1992 11 12
Mechanical properties of fasteners — Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
Norm
ISO 965-1:1998
Issue date : 1998 12 20
ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data
Norm
ISO 965-2:1998
Issue date : 1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
Norm
ISO 6157-1:1988
Issue date : 1988 07 28
Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements (Corrected version 1992-07)
Norm
ISO 6157-3:1988
Issue date : 1988 07 21
Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements (Corrected version 1992-07)
Norm
ISO 6506:1981
Issue date : 1981 09 01
Metallic materials — Hardness test — Brinell test
Norm
ISO 6507-1:1997
Issue date : 1997 11 20
Metallic materials — Vickers hardness test — Part 1: Test method
Norm
ISO 6508:1986
Issue date : 1986 11 13
Metallic materials — Hardness test — Rockwell test (scales A - B - C - D - E - F - G - H - K)
Norm
ISO 6892:1998
Issue date : 1998 03 05
Metallic materials — Tensile testing at ambient temperature
Norm
ÖNORM EN ISO 898-1
Issue date : 2009 10 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2009)
Norm
ISO 898-1:1999
Issue date : 1999 08 26
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs