Please select and order
€109.76
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 3269

Issue date: 2000 11 01

Fasteners - Acceptance inspection (ISO 3269:2000)

1.1 This International Standard specifies the acceptance inspection procedure that the purchaser of fasteners must follow in order to determine whether a lot of fasteners...
Withdrawn: 2020 01 01
Publisher:
Austrian Standards International
Format:
Digital | 23 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
1.1 This International Standard specifies the acceptance inspection procedure that the purchaser of fasteners must follow in order to determine whether a lot of fasteners will be accepted or rejected in cases where no other such procedure was agreed with the supplier at the time the fasteners were ordered. Additional requirements for acceptance may be included in a specific product standard (for example, one on prevailing torque-type nuts). The same procedure is also to be applied in cases where conformance to specification is disputed. 1.2 This International Standard is applicable to bolts, screws, studs, nuts, pins, washers, blind rivets and other related fasteners not intended for high volume machine assembly, special-purpose applications or specially engineered applications requiring greater in-process control and lot traceability (see the note in the introduction). The procedure for these products shall be agreed upon by the supplier and the purchaser prior to the confirmation of the order. 1.3 This International Standard is applicable only to fully manufactured products; it neither implies nor includes any particular in-process control procedure or inspection during production. 1.4 The production of accessories, services and partially fabricated parts (for example, washers, nuts, plating, heat treatment and blanks) for use in the manufacture of fasteners may be subcontracted to other suppliers by the fastener supplier. Nevertheless, the supplier of the final, finished product shall be solely responsible for the fastener s quality. The requirements of this International Standard apply only to the condition of fasteners at the time of delivery. Any process carried out after receipt (for example, plating) will invalidate the requirements of this International Standard. 1.5 Annex B (informative) offers guidance to, and an explanation of, the principles upon which this International Standard is based.
ÖNORM EN ISO 3269
2020 01 01
Fasteners - Acceptance inspection (ISO 3269:2019)
Norm
ÖNORM EN ISO 3269
2000 11 01
Fasteners - Acceptance inspection (ISO 3269:2000)
Norm
Norm
ISO 10683:2000
Issue date : 2000 07 27
Fasteners — Non-electrolytically applied zinc flake coatings
Norm
ISO 4759-1:2000
Issue date : 2000 11 09
Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
Norm
ÖNORM EN 20898-2
Issue date : 1994 05 01
Mechanical properties of fasteners - Part 2 : Nuts with specified proof load values - Coarse thread (ISO 898-2:1992)
Norm
ÖNORM EN 26157-1
Issue date : 1992 03 01
Fasteners - Surface discontinuities - Bolts, screws and studs for general requirements
Norm
ÖNORM EN 26157-3
Issue date : 1992 03 01
Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements
Norm
ÖNORM EN 28839
Issue date : 1992 03 01
Mechanical properties of fasteners - Bolts, screws, studs and nuts made of nonferrous metals
Norm
ÖNORM EN ISO 1478
Issue date : 1999 12 01
Tapping screw thread (ISO 1478:1999)
Norm
ÖNORM EN ISO 2320
Issue date : 2009 02 15
Prevailing torque type steel nuts - Mechanical and performance properties (ISO 2320:2008)
Norm
ÖNORM EN ISO 2702
Issue date : 1994 10 01
Heat-treated steel tapping screws - Mechanical properties (ISO 2702:1992)
Norm
ÖNORM EN ISO 3506-1
Issue date : 1998 05 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:1997)
Norm
ÖNORM EN ISO 3506-1
Issue date : 2008 06 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 1: Bolts, screws and studs (ISO/DIS 3506-1:2008)
Norm
ÖNORM EN ISO 3506-2
Issue date : 1998 05 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 2: Nuts (ISO 3506-2:1997)
Norm
ÖNORM EN ISO 3506-2
Issue date : 2008 06 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 2: Nuts (ISO/DIS 3506-2:2008)
Norm
ÖNORM EN ISO 3506-3
Issue date : 1998 05 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997)
Norm
ÖNORM EN ISO 3506-3
Issue date : 2008 06 01
Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO/DIS 3506-3:2008)
Norm
ÖNORM EN ISO 4042
Issue date : 1999 12 01
Fasteners - Electroplated coatings (ISO 4042:1999)
Norm
ÖNORM EN ISO 4759-3
Issue date : 2000 11 01
Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts - Product grades A and C (ISO 4759-3:2000)
Norm
ÖNORM EN ISO 7085
Issue date : 2000 02 01
Mechanical and performance requirements of case hardened and tempered metric thread rolling screws (ISO 7085:1999)
Norm
ÖNORM EN ISO 898-1
Issue date : 1999 12 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999)
Norm
ÖNORM EN ISO 898-1
Issue date : 2007 02 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO/DIS 898-1:2006)
Norm
ÖNORM EN ISO 898-5
Issue date : 1998 11 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners not under tensile stresses (ISO 898-5:1998)
Norm
ÖNORM EN ISO 898-6
Issue date : 1996 03 01
Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994)
Norm
ISO 898-1:1999
Issue date : 1999 08 26
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs
Norm
ISO 898-2:1992
Issue date : 1992 11 12
Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse thread
Norm
ISO 898-5:1998
Issue date : 1998 07 23
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners not under tensile stresses
Norm
ISO 898-6:1994
Issue date : 1994 12 15
Mechanical properties of fasteners — Part 6: Nuts with specified proof load values — Fine pitch thread
Norm
ISO 1478:1999
Issue date : 1999 11 04
Tapping screws thread
Norm
ISO 1502:1996
Issue date : 1996 01 17
ISO general-purpose metric screw threads — Gauges and gauging
Norm
ISO 2320:1997
Issue date : 1997 10 30
Prevailing torque type steel hexagon nuts — Mechanical and performance properties
Norm
ISO 2702:1992
Issue date : 1992 03 25
Heat-treated steel tapping screws — Mechanical properties
Norm
ISO 2859-1:1999
Issue date : 1999 11 18
Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
Norm
ISO 3506-1:1997
Issue date : 1997 11 20
Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs
Norm
ISO 3506-2:1997
Issue date : 1997 11 20
Mechanical properties of corrosion-resistant stainless-steel fasteners — Part 2: Nuts
Norm
ISO 3506-3:1997
Issue date : 1997 11 20
Mechanical properties of corrosion-resistant stainless-steel fasteners — Part 3: Set screws and similar fasteners not under tensile stress
Norm
ISO 4042:1999
Issue date : 1999 07 01
Fasteners — Electroplated coatings
Norm
ISO 4759-1:2000
Issue date : 2000 11 09
Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
Norm
ISO 4759-3:2000
Issue date : 2000 05 11
Tolerances for fasteners — Part 3: Plain washers for bolts, screws and nuts — Product grades A and C
Norm
ISO 6157-1:1988
Issue date : 1988 07 28
Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements (Corrected version 1992-07)
Norm
ISO 6157-2:1995
Issue date : 1995 07 20
Fasteners — Surface discontinuities — Part 2: Nuts
Norm
ISO 6157-3:1988
Issue date : 1988 07 21
Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements (Corrected version 1992-07)
Norm
ISO 7085:1999
Issue date : 1999 09 09
Mechanical and performance requirements of case hardened and tempered metric thread rolling screws
Norm
ISO 8839:1986
Issue date : 1986 12 11
Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals
Norm
ISO 10683:2018
Issue date : 2018 08 13
Fasteners — Non-electrolytically applied zinc flake coating systems
Norm
ÖNORM EN ISO 3269
Issue date : 2020 01 01
Fasteners - Acceptance inspection (ISO 3269:2019)
Norm
ISO 3269:2000
Issue date : 2000 05 25
Fasteners — Acceptance inspection