Please select and order
€72.72
excl. VAT
Add to cart
Norm

ÖNORM EN 12201-5

Issue date: 2012 03 01

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system

This Part of EN 12201 specifies the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water intended for human co...
Withdrawn: 2024 08 01
This Part of EN 12201 specifies the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water intended for human consumption, including raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. It also specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. In conjunction with Parts 1 to 4 of EN 12201 it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar; b) an operating temperature of 20 °C as a reference temperature. c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges.
ÖNORM EN 12201-5
2024 08 01
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (P...
Norm
ÖNORM EN 12201-5
2012 03 01
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylen...
Norm
ÖNORM EN 12201-5
2003 08 01
Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the sy...
Norm
ÖNORM EN 13244-5
2003 08 01
Plastics piping systems for buried and above-ground pressure systems for water for general purposes,...
Norm
Expand
Norm
ISO 13953:2001
Issue date : 2001 10 25
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
Norm
ISO 13954:1997
Issue date : 1997 12 25
Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
Norm
ISO 13955:1997
Issue date : 1997 12 25
Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies
Norm
ISO 13956:2010
Issue date : 2010 09 22
Plastics pipes and fittings — Decohesion test of polyethylene (PE) saddle fusion joints — Evaluation of ductility of fusion joint interface by tear test
Norm
ÖNORM EN 712
Issue date : 1994 03 01
Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
Norm
ÖNORM EN 713
Issue date : 1994 03 01
Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies ......(abbreviated)
Norm
ÖNORM EN 715
Issue date : 1994 03 01
Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings - Test method for leaktightness under internal water .......(abbreviated)
Norm
ÖNORM EN 911
Issue date : 1996 11 01
Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under .........(abbreviated)
Norm
ÖNORM EN 12201-4
Issue date : 2012 03 01
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
Norm
ÖNORM EN 12201-3
Issue date : 2012 03 01
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
Norm
ÖNORM EN 12201-2
Issue date : 2012 03 01
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
Norm
ÖNORM EN ISO 1167-1
Issue date : 2006 07 01
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
Norm
ÖNORM EN ISO 1167-2
Issue date : 2006 07 01
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
Norm
ÖNORM EN ISO 1167-4
Issue date : 2008 03 01
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
Norm
ÖNORM EN 12201-1
Issue date : 2012 03 01
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
Norm
ISO 11413:2008
Issue date : 2008 12 11
Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
Norm
ISO 11414:2009
Issue date : 2009 01 29
Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
Norm
ISO 13953:2001
Issue date : 2001 10 25
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
Norm
ISO 13954:1997
Issue date : 1997 12 25
Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
Norm
ISO 13955:1997
Issue date : 1997 12 25
Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies
Norm
ISO 13956:2010
Issue date : 2010 09 22
Plastics pipes and fittings — Decohesion test of polyethylene (PE) saddle fusion joints — Evaluation of ductility of fusion joint interface by tear test
Norm
ISO 14236:2000
Issue date : 2000 03 23
Plastics pipes and fittings — Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
Norm
ÖNORM EN 12201-5
Issue date : 2024 08 01
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system