Jetzt auswählen und bestellen
84,27 €
exkl. USt.
In den Warenkorb
Norm

ÖNORM EN 14870-3

Ausgabedatum: 2006 05 01

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004 modified)

This part of EN 14870 applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges. This pa...
Gültig
This part of EN 14870 applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges. This part of EN 14870 specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This part of EN 14870 designates those categories of flanges that meet the industrys need to match ISO 3183 pipe. These flanges are for normal and low-temperature service and include supplementary requirements where required for sour service. Materials for, or the attachment of, factory-welded extensions, bolting materials, gaskets, slip-on flanges or flanged fittings are not covered by this part of EN 14870. This part of EN 14870 is not applicable to integrally cast or forged flanges for valves, pumps or other equipment. This part of EN 14870 does not cover the selection of the flange category or pressure class. Sizes and pressure classes listed in ISO 7005-1 and applicable to this part of EN 14870 are as follows: DN 10 (NPS 1/2) to DN 1500 (NPS 60); PN 20 (class 150), PN 50 (class 300), PN 100 (class 600), PN 150 (class 900), PN 250 (class 1500), PN 420 (class 2500). On-land supply systems used by the gas supply industry are excluded from the scope of this document.
ÖNORM EN 14870-3
2006 05 01
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transporta...
Norm
Norm
ISO 11496:1993
Ausgabedatum : 1993 11 11
Seamless and welded steel tubes for pressure purposes — Ultrasonic testing of tube ends for the detection of laminar imperfections
Norm
ISO 12095:1994
Ausgabedatum : 1994 12 15
Seamless and welded steel tubes for pressure purposes — Liquid penetrant testing
Norm
ISO 13623:2000
Ausgabedatum : 2000 04 13
Petroleum and natural gas industries — Pipeline transportation systems
Schlussentwurf
ISO/FDIS 13623
Ausgabedatum : 2009 03 18
Petroleum and natural gas industries — Pipeline transportation systems
Norm
ISO 13664:1997
Ausgabedatum : 1997 05 01
Seamless and welded steel tubes for pressure purposes — Magnetic particle inspection of the tube ends for the detection of laminar imperfections
Norm
ISO 13665:1997
Ausgabedatum : 1997 05 01
Seamless and welded steel tubes for pressure purposes — Magnetic particle inspection of the tube body for the detection of surface imperfections
Norm
ISO 148-1:2006
Ausgabedatum : 2006 02 17
Metallic materials — Charpy pendulum impact test — Part 1: Test method
Norm
ISO 2566-1:1984
Ausgabedatum : 1984 07 01
Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels
Norm
ISO 377:1997
Ausgabedatum : 1997 07 10
Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
Norm
ISO 4885:1996
Ausgabedatum : 1996 03 14
Ferrous products — Heat treatments — Vocabulary
Norm
ISO 6892:1998
Ausgabedatum : 1998 03 05
Metallic materials — Tensile testing at ambient temperature
Entwurf
ISO/DIS 6892
Ausgabedatum : 2007 02 08
Metallic materials — Tensile testing — Method of testing at ambient temperature
Norm
ISO 783:1999
Ausgabedatum : 1999 08 26
Metallic materials — Tensile testing at elevated temperature
Norm
ISO 9327-1:1999
Ausgabedatum : 1999 04 22
Steel forgings and rolled or forged bars for pressure purposes — Technical delivery conditions — Part 1: General requirements
Norm
ISO 9712:2005
Ausgabedatum : 2005 02 17
Non-destructive testing — Qualification and certification of personnel (Corrected version 2005-03)
Norm
ÖNORM EN 14870-1
Ausgabedatum : 2005 03 01
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)
Norm
ÖNORM EN 14870-2
Ausgabedatum : 2005 08 01
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)
Norm
ISO 148-1:2016
Ausgabedatum : 2016 10 12
Metallic materials — Charpy pendulum impact test — Part 1: Test method
Norm
ISO 377:2017
Ausgabedatum : 2017 06 16
Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
Norm
ISO 2566-1:1984
Ausgabedatum : 1984 07 01
Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels
Norm
ISO 3183-1:1996
Ausgabedatum : 1996 10 17
Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 1: Pipes of requirement class A
Norm
ISO 3183-2:1996
Ausgabedatum : 1996 03 14
Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 2: Pipes of requirements class B
Norm
ISO 3183-3:1999
Ausgabedatum : 1999 04 15
Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 3: Pipes of requirement class C
Norm
ISO 4885:2018
Ausgabedatum : 2018 02 28
Ferrous materials — Heat treatments — Vocabulary
Norm
ISO 6507-1:1997
Ausgabedatum : 1997 11 20
Metallic materials — Vickers hardness test — Part 1: Test method
Norm
ISO 6892:1998
Ausgabedatum : 1998 03 05
Metallic materials — Tensile testing at ambient temperature
Norm
ISO 7005-1:1992
Ausgabedatum : 1992 04 09
Metallic flanges — Part 1: Steel flanges
Technische Regel
ISO/TR 7705:1991
Ausgabedatum : 1991 11 14
Guidelines for specifying Charpy V-notch impact prescriptions in steel specifications
Norm
ISO 9327-1:1999
Ausgabedatum : 1999 04 22
Steel forgings and rolled or forged bars for pressure purposes — Technical delivery conditions — Part 1: General requirements
Norm
ISO 10474:1991
Ausgabedatum : 1991 12 05
Steel and steel products — Inspection documents
Norm
ISO 11496:1993
Ausgabedatum : 1993 11 11
Seamless and welded steel tubes for pressure purposes — Ultrasonic testing of tube ends for the detection of laminar imperfections
Norm
ISO 12095:1994
Ausgabedatum : 1994 12 15
Seamless and welded steel tubes for pressure purposes — Liquid penetrant testing
Norm
ISO 13623:2017
Ausgabedatum : 2017 09 29
Petroleum and natural gas industries — Pipeline transportation systems
Norm
ISO 13664:1997
Ausgabedatum : 1997 05 01
Seamless and welded steel tubes for pressure purposes — Magnetic particle inspection of the tube ends for the detection of laminar imperfections
Norm
ISO 13665:1997
Ausgabedatum : 1997 05 01
Seamless and welded steel tubes for pressure purposes — Magnetic particle inspection of the tube body for the detection of surface imperfections
Norm
ISO 15156-2:2003
Ausgabedatum : 2003 12 05
Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons